// Copy this file to config_user.h and adjust it to your needs.


#ifndef __CONFIG_USER_H__
#define __CONFIG_USER_H__

// Debug output on the serial console
#define DEBUG

// Device name
// WARNING: Keep the name short! If your access point did not show up, you
// maybe have a TOO LONG SSID!
String DEVICE_NAME = "weatherstation";

// Enable/Disable features
#define USE_WIFIMANAGER
//#define WEBUPDATER_FEATURE
#define INFLUXDB_FEATURE
#define INFLUXDB_VERSION 1 // 1 or 2
#define SERIAL_FEATURE
//#define BATTERY_POWERED
//#define SENSOR_WIND
#define SENSOR_APDS9960
//#define SENSOR_APDS9930
#define SENSOR_BME280
#define SENSOR_BATTERY
//#define BAT_PINS_D34
// Homebridge Webstat is only possible if webupdater is also enabled
//#define HOMEBRIDGE_WEBSTAT
// retries to connect after 5 seconds or starts the wifimanager
#define SLEEP_IF_NO_WLAN_CONNECTION
// Restarts the firmware every n seconds
//#define RESET_ESP_TIMEINTERVAL // BETA STATUS
//#define HTTP_CALL_ON_WINDSPEED_EXCEED  // BETA STATUS
//#define DEBUG_WINDSPEED_MEASUREMENT   // for debugging windspeed measurement only
//#define LOG_MILLIS_TO_INFLUXDB
//#define ENABLE_WATCHDOG
//#define WATCHDOG_TIMEOUT_MS 30000

const float HUMIDITY_FACTOR = 1.0;
const float LIGHT_FACTOR    = 1.0;
const float TEMP_FACTOR     = 1.0;

// InfluxDB credentials
const char     *INFLUXDB_HOST = "hostname";
const uint16_t  INFLUXDB_PORT = 80;
const char     *INFLUXDB_DB   = "database";
const char     *INFLUXDB_USER = "user";
const char     *INFLUXDB_PASS = "password";

// InfluxDB2 credentials
/*
const char *INFLUXDB_URL    = "http://192.168.0.123:3124";
const char *INFLUXDB_ORG    = "home_org";
const char *INFLUXDB_BUCKET = "mybucket";
const char *INFLUXDB_TOKEN  = "your api token";
*/

// enable HTTP_CALL_ON_WINDSPEED_EXCEED to enable this feature
#define HTTP_CALL_ON_WINDSPEED_EXCEED_MPS  5.0 // 5.0 m/s == 18 km/h
#define HTTP_CALL_ON_WINDSPEED_INTERVAL_S   60 // it's required to be bigger than WIND_SENSOR_MEAS_TIME_S
#define HTTP_CALL_ON_WINDSPEED_URL         "http://192.168.178.100:3001/button-windspeedexceed?event=click"

// anemometer settings
// thingiverse anemometer settings: https://www.thingiverse.com/thing:2559929/files
#define ROTOR_LENGTH_CM                             8.25
#define ROTOR_LENGTH_M          (ROTOR_LENGTH_CM / 100.0)
//#define ROTOR_LENGTH_KM       (ROTOR_LENGTH_M / 1000.0) // configuration example for generalization
//#define SEC_TO_HOUR_FACTOR                (60.0 * 60.0) // configuration example for generalization
#define MPS_CORRECT_FACT                            9.28
//#define COUNT_TO_KMH          ((TWO_PI * ROTOR_LENGTH_KM / WIND_SENSOR_MEAS_TIME_S) * SEC_TO_HOUR_FACTOR) // configuration exampe for generalization
#define COUNT_TO_MPS             (TWO_PI * ROTOR_LENGTH_M  / WIND_SENSOR_MEAS_TIME_S)
// only this define is used for calculation, all other before are only used to describe the math v_wind = correction_factor * rotations * 2 * pi * radius / time_of_measurement_in_sec
// and if required the result has t be multiplied by another factor to convert it from m/s
#define WINDSPEED_FACTOR         (COUNT_TO_MPS * MPS_CORRECT_FACT)

// china aliexpress anemometer settings (calculation unknown) <add link here>
//#define WINDSPEED_FACTOR 2.4

#ifndef USE_WIFIMANAGER

// Set IP address
IPAddress local_IP(192, 168, 178, 123);
// Set your Gateway IP address
IPAddress gateway(192, 168, 178, 1);
// Set subnet mask
IPAddress subnet(255, 255, 255, 0);

const char* ssid     =  "My-WLAN-SSID"; // WLAN Netzwerk
const char* password = "My-Passphrase"; // WLAN Passphrase

#endif