weatherstation/firmware/libraries/Adafruit_BusIO/Adafruit_SPIDevice.cpp
2022-11-11 11:11:25 +01:00

508 lines
13 KiB
C++

#include "Adafruit_SPIDevice.h"
//#define DEBUG_SERIAL Serial
/*!
* @brief Create an SPI device with the given CS pin and settings
* @param cspin The arduino pin number to use for chip select
* @param freq The SPI clock frequency to use, defaults to 1MHz
* @param dataOrder The SPI data order to use for bits within each byte,
* defaults to SPI_BITORDER_MSBFIRST
* @param dataMode The SPI mode to use, defaults to SPI_MODE0
* @param theSPI The SPI bus to use, defaults to &theSPI
*/
Adafruit_SPIDevice::Adafruit_SPIDevice(int8_t cspin, uint32_t freq,
BusIOBitOrder dataOrder,
uint8_t dataMode, SPIClass *theSPI) {
#ifdef BUSIO_HAS_HW_SPI
_cs = cspin;
_sck = _mosi = _miso = -1;
_spi = theSPI;
_begun = false;
_spiSetting = new SPISettings(freq, dataOrder, dataMode);
_freq = freq;
_dataOrder = dataOrder;
_dataMode = dataMode;
#else
// unused, but needed to suppress compiler warns
(void)cspin;
(void)freq;
(void)dataOrder;
(void)dataMode;
(void)theSPI;
#endif
}
/*!
* @brief Create an SPI device with the given CS pin and settings
* @param cspin The arduino pin number to use for chip select
* @param sckpin The arduino pin number to use for SCK
* @param misopin The arduino pin number to use for MISO, set to -1 if not
* used
* @param mosipin The arduino pin number to use for MOSI, set to -1 if not
* used
* @param freq The SPI clock frequency to use, defaults to 1MHz
* @param dataOrder The SPI data order to use for bits within each byte,
* defaults to SPI_BITORDER_MSBFIRST
* @param dataMode The SPI mode to use, defaults to SPI_MODE0
*/
Adafruit_SPIDevice::Adafruit_SPIDevice(int8_t cspin, int8_t sckpin,
int8_t misopin, int8_t mosipin,
uint32_t freq, BusIOBitOrder dataOrder,
uint8_t dataMode) {
_cs = cspin;
_sck = sckpin;
_miso = misopin;
_mosi = mosipin;
#ifdef BUSIO_USE_FAST_PINIO
csPort = (BusIO_PortReg *)portOutputRegister(digitalPinToPort(cspin));
csPinMask = digitalPinToBitMask(cspin);
if (mosipin != -1) {
mosiPort = (BusIO_PortReg *)portOutputRegister(digitalPinToPort(mosipin));
mosiPinMask = digitalPinToBitMask(mosipin);
}
if (misopin != -1) {
misoPort = (BusIO_PortReg *)portInputRegister(digitalPinToPort(misopin));
misoPinMask = digitalPinToBitMask(misopin);
}
clkPort = (BusIO_PortReg *)portOutputRegister(digitalPinToPort(sckpin));
clkPinMask = digitalPinToBitMask(sckpin);
#endif
_freq = freq;
_dataOrder = dataOrder;
_dataMode = dataMode;
_begun = false;
}
/*!
* @brief Release memory allocated in constructors
*/
Adafruit_SPIDevice::~Adafruit_SPIDevice() {
if (_spiSetting)
delete _spiSetting;
}
/*!
* @brief Initializes SPI bus and sets CS pin high
* @return Always returns true because there's no way to test success of SPI
* init
*/
bool Adafruit_SPIDevice::begin(void) {
if (_cs != -1) {
pinMode(_cs, OUTPUT);
digitalWrite(_cs, HIGH);
}
if (_spi) { // hardware SPI
#ifdef BUSIO_HAS_HW_SPI
_spi->begin();
#endif
} else {
pinMode(_sck, OUTPUT);
if ((_dataMode == SPI_MODE0) || (_dataMode == SPI_MODE1)) {
// idle low on mode 0 and 1
digitalWrite(_sck, LOW);
} else {
// idle high on mode 2 or 3
digitalWrite(_sck, HIGH);
}
if (_mosi != -1) {
pinMode(_mosi, OUTPUT);
digitalWrite(_mosi, HIGH);
}
if (_miso != -1) {
pinMode(_miso, INPUT);
}
}
_begun = true;
return true;
}
/*!
* @brief Transfer (send/receive) a buffer over hard/soft SPI, without
* transaction management
* @param buffer The buffer to send and receive at the same time
* @param len The number of bytes to transfer
*/
void Adafruit_SPIDevice::transfer(uint8_t *buffer, size_t len) {
//
// HARDWARE SPI
//
if (_spi) {
#ifdef BUSIO_HAS_HW_SPI
#if defined(SPARK)
_spi->transfer(buffer, buffer, len, nullptr);
#elif defined(STM32)
for (size_t i = 0; i < len; i++) {
_spi->transfer(buffer[i]);
}
#else
_spi->transfer(buffer, len);
#endif
return;
#endif
}
//
// SOFTWARE SPI
//
uint8_t startbit;
if (_dataOrder == SPI_BITORDER_LSBFIRST) {
startbit = 0x1;
} else {
startbit = 0x80;
}
bool towrite, lastmosi = !(buffer[0] & startbit);
uint8_t bitdelay_us = (1000000 / _freq) / 2;
for (size_t i = 0; i < len; i++) {
uint8_t reply = 0;
uint8_t send = buffer[i];
/*
Serial.print("\tSending software SPI byte 0x");
Serial.print(send, HEX);
Serial.print(" -> 0x");
*/
// Serial.print(send, HEX);
for (uint8_t b = startbit; b != 0;
b = (_dataOrder == SPI_BITORDER_LSBFIRST) ? b << 1 : b >> 1) {
if (bitdelay_us) {
delayMicroseconds(bitdelay_us);
}
if (_dataMode == SPI_MODE0 || _dataMode == SPI_MODE2) {
towrite = send & b;
if ((_mosi != -1) && (lastmosi != towrite)) {
#ifdef BUSIO_USE_FAST_PINIO
if (towrite)
*mosiPort |= mosiPinMask;
else
*mosiPort &= ~mosiPinMask;
#else
digitalWrite(_mosi, towrite);
#endif
lastmosi = towrite;
}
#ifdef BUSIO_USE_FAST_PINIO
*clkPort |= clkPinMask; // Clock high
#else
digitalWrite(_sck, HIGH);
#endif
if (bitdelay_us) {
delayMicroseconds(bitdelay_us);
}
if (_miso != -1) {
#ifdef BUSIO_USE_FAST_PINIO
if (*misoPort & misoPinMask) {
#else
if (digitalRead(_miso)) {
#endif
reply |= b;
}
}
#ifdef BUSIO_USE_FAST_PINIO
*clkPort &= ~clkPinMask; // Clock low
#else
digitalWrite(_sck, LOW);
#endif
} else { // if (_dataMode == SPI_MODE1 || _dataMode == SPI_MODE3)
#ifdef BUSIO_USE_FAST_PINIO
*clkPort |= clkPinMask; // Clock high
#else
digitalWrite(_sck, HIGH);
#endif
if (bitdelay_us) {
delayMicroseconds(bitdelay_us);
}
if (_mosi != -1) {
#ifdef BUSIO_USE_FAST_PINIO
if (send & b)
*mosiPort |= mosiPinMask;
else
*mosiPort &= ~mosiPinMask;
#else
digitalWrite(_mosi, send & b);
#endif
}
#ifdef BUSIO_USE_FAST_PINIO
*clkPort &= ~clkPinMask; // Clock low
#else
digitalWrite(_sck, LOW);
#endif
if (_miso != -1) {
#ifdef BUSIO_USE_FAST_PINIO
if (*misoPort & misoPinMask) {
#else
if (digitalRead(_miso)) {
#endif
reply |= b;
}
}
}
if (_miso != -1) {
buffer[i] = reply;
}
}
}
return;
}
/*!
* @brief Transfer (send/receive) one byte over hard/soft SPI, without
* transaction management
* @param send The byte to send
* @return The byte received while transmitting
*/
uint8_t Adafruit_SPIDevice::transfer(uint8_t send) {
uint8_t data = send;
transfer(&data, 1);
return data;
}
/*!
* @brief Manually begin a transaction (calls beginTransaction if hardware
* SPI)
*/
void Adafruit_SPIDevice::beginTransaction(void) {
if (_spi) {
#ifdef BUSIO_HAS_HW_SPI
_spi->beginTransaction(*_spiSetting);
#endif
}
}
/*!
* @brief Manually end a transaction (calls endTransaction if hardware SPI)
*/
void Adafruit_SPIDevice::endTransaction(void) {
if (_spi) {
#ifdef BUSIO_HAS_HW_SPI
_spi->endTransaction();
#endif
}
}
/*!
* @brief Assert/Deassert the CS pin if it is defined
* @param value The state the CS is set to
*/
void Adafruit_SPIDevice::setChipSelect(int value) {
if (_cs != -1) {
digitalWrite(_cs, value);
}
}
/*!
* @brief Write a buffer or two to the SPI device, with transaction
* management.
* @brief Manually begin a transaction (calls beginTransaction if hardware
* SPI) with asserting the CS pin
*/
void Adafruit_SPIDevice::beginTransactionWithAssertingCS() {
beginTransaction();
setChipSelect(LOW);
}
/*!
* @brief Manually end a transaction (calls endTransaction if hardware SPI)
* with deasserting the CS pin
*/
void Adafruit_SPIDevice::endTransactionWithDeassertingCS() {
setChipSelect(HIGH);
endTransaction();
}
/*!
* @brief Write a buffer or two to the SPI device, with transaction
* management.
* @param buffer Pointer to buffer of data to write
* @param len Number of bytes from buffer to write
* @param prefix_buffer Pointer to optional array of data to write before
* buffer.
* @param prefix_len Number of bytes from prefix buffer to write
* @return Always returns true because there's no way to test success of SPI
* writes
*/
bool Adafruit_SPIDevice::write(const uint8_t *buffer, size_t len,
const uint8_t *prefix_buffer,
size_t prefix_len) {
beginTransactionWithAssertingCS();
// do the writing
#if defined(ARDUINO_ARCH_ESP32)
if (_spi) {
if (prefix_len > 0) {
_spi->transferBytes(prefix_buffer, nullptr, prefix_len);
}
if (len > 0) {
_spi->transferBytes(buffer, nullptr, len);
}
} else
#endif
{
for (size_t i = 0; i < prefix_len; i++) {
transfer(prefix_buffer[i]);
}
for (size_t i = 0; i < len; i++) {
transfer(buffer[i]);
}
}
endTransactionWithDeassertingCS();
#ifdef DEBUG_SERIAL
DEBUG_SERIAL.print(F("\tSPIDevice Wrote: "));
if ((prefix_len != 0) && (prefix_buffer != nullptr)) {
for (uint16_t i = 0; i < prefix_len; i++) {
DEBUG_SERIAL.print(F("0x"));
DEBUG_SERIAL.print(prefix_buffer[i], HEX);
DEBUG_SERIAL.print(F(", "));
}
}
for (uint16_t i = 0; i < len; i++) {
DEBUG_SERIAL.print(F("0x"));
DEBUG_SERIAL.print(buffer[i], HEX);
DEBUG_SERIAL.print(F(", "));
if (i % 32 == 31) {
DEBUG_SERIAL.println();
}
}
DEBUG_SERIAL.println();
#endif
return true;
}
/*!
* @brief Read from SPI into a buffer from the SPI device, with transaction
* management.
* @param buffer Pointer to buffer of data to read into
* @param len Number of bytes from buffer to read.
* @param sendvalue The 8-bits of data to write when doing the data read,
* defaults to 0xFF
* @return Always returns true because there's no way to test success of SPI
* writes
*/
bool Adafruit_SPIDevice::read(uint8_t *buffer, size_t len, uint8_t sendvalue) {
memset(buffer, sendvalue, len); // clear out existing buffer
beginTransactionWithAssertingCS();
transfer(buffer, len);
endTransactionWithDeassertingCS();
#ifdef DEBUG_SERIAL
DEBUG_SERIAL.print(F("\tSPIDevice Read: "));
for (uint16_t i = 0; i < len; i++) {
DEBUG_SERIAL.print(F("0x"));
DEBUG_SERIAL.print(buffer[i], HEX);
DEBUG_SERIAL.print(F(", "));
if (len % 32 == 31) {
DEBUG_SERIAL.println();
}
}
DEBUG_SERIAL.println();
#endif
return true;
}
/*!
* @brief Write some data, then read some data from SPI into another buffer,
* with transaction management. The buffers can point to same/overlapping
* locations. This does not transmit-receive at the same time!
* @param write_buffer Pointer to buffer of data to write from
* @param write_len Number of bytes from buffer to write.
* @param read_buffer Pointer to buffer of data to read into.
* @param read_len Number of bytes from buffer to read.
* @param sendvalue The 8-bits of data to write when doing the data read,
* defaults to 0xFF
* @return Always returns true because there's no way to test success of SPI
* writes
*/
bool Adafruit_SPIDevice::write_then_read(const uint8_t *write_buffer,
size_t write_len, uint8_t *read_buffer,
size_t read_len, uint8_t sendvalue) {
beginTransactionWithAssertingCS();
// do the writing
#if defined(ARDUINO_ARCH_ESP32)
if (_spi) {
if (write_len > 0) {
_spi->transferBytes(write_buffer, nullptr, write_len);
}
} else
#endif
{
for (size_t i = 0; i < write_len; i++) {
transfer(write_buffer[i]);
}
}
#ifdef DEBUG_SERIAL
DEBUG_SERIAL.print(F("\tSPIDevice Wrote: "));
for (uint16_t i = 0; i < write_len; i++) {
DEBUG_SERIAL.print(F("0x"));
DEBUG_SERIAL.print(write_buffer[i], HEX);
DEBUG_SERIAL.print(F(", "));
if (write_len % 32 == 31) {
DEBUG_SERIAL.println();
}
}
DEBUG_SERIAL.println();
#endif
// do the reading
for (size_t i = 0; i < read_len; i++) {
read_buffer[i] = transfer(sendvalue);
}
#ifdef DEBUG_SERIAL
DEBUG_SERIAL.print(F("\tSPIDevice Read: "));
for (uint16_t i = 0; i < read_len; i++) {
DEBUG_SERIAL.print(F("0x"));
DEBUG_SERIAL.print(read_buffer[i], HEX);
DEBUG_SERIAL.print(F(", "));
if (read_len % 32 == 31) {
DEBUG_SERIAL.println();
}
}
DEBUG_SERIAL.println();
#endif
endTransactionWithDeassertingCS();
return true;
}
/*!
* @brief Write some data and read some data at the same time from SPI
* into the same buffer, with transaction management. This is basicaly a wrapper
* for transfer() with CS-pin and transaction management. This /does/
* transmit-receive at the same time!
* @param buffer Pointer to buffer of data to write/read to/from
* @param len Number of bytes from buffer to write/read.
* @return Always returns true because there's no way to test success of SPI
* writes
*/
bool Adafruit_SPIDevice::write_and_read(uint8_t *buffer, size_t len) {
beginTransactionWithAssertingCS();
transfer(buffer, len);
endTransactionWithDeassertingCS();
return true;
}