mini-led-cube/firmware/main.c

/*
 * CTHN.de MiniLEDCube
 *
 *  By Kai Lauterbach (klaute at web dot de) 11/2011
 *
 *  Based on http://mosfetkiller.de/?s=miniledcube
 *
 *  License: General Public License (GPL v3)
 *
 */

#include "main.h"

// Main loop
int __attribute__((OS_main))
main()
{
    // Initialize the AVR and the USB connection.
    init();
    init_usb();

    // Hauptschleife
    for (;;)
    {
        usbPoll(); // keep connected
    }
}

// Initialisierung
void init()
{
    // Init ports
    DDRB  = 0b11111111;    // PB0-PB7: LED 1-8 (Kathode)
    PORTB = 0b11111111;    // HIGH

    DDRD  = 0b01111000;    // PD6: LED 9 (Kathode); PD5-PD3: A-C (Anoden)
    PORTD = 0b01000000;

    // Setup Timer-Interrupt "TIMER1"
    TIMSK |= (1 << OCIE1A);

    // Refreshrate is 100Hz
    // Set the compare value
    // 625d = 0x271 = 0b00000010, 0b01110001
    OCR1AH = 0b00000010;
    OCR1AL = 0b01110001;

    // anpassen auf reihenweise ausgabe
    // prescale is 64 (0x011) ----> CS12=0, CS11=1, CS10=1
    TCCR1B |= (1 << CS11) | (1 << CS10) | (1 << WGM12);

    sei(); // Enable interrupts global
}

// TIMER1 Interruptvector
ISR (TIMER1_COMPA_vect)
{

    //delay--; // decrease the delay counter
    if ( !(--delay) ) // check if we are done with waiting
    {
        if (frmnum == MAX_EEPROM_FRAMES)
        {
            if (mode == MODE_ANIMATION_SINGLE)
                mode = MODE_ANIMATION_STOP; // stop the animation after we have reached the 31th frame
            frmnum = 0; // always start at the first frame
        } else {
            if (mode)
            {
                // if we are in an animation mode we have to load a frame out of the eeprom
                // and increase the counter
                frame = eeprom_read_dword( &eep_anim[frmnum] );
                frmnum++;
            }
        }
        delay = (frame & 0xf8000000) >> 24; // Just shift right by 24 instead of 27 to multiply the delay by 8.
    }

	// PORTD = __, 9, C, B, A,D+,D-,__
    PORTD &= 0b10000111; // delete bit 3 to 6 (bit 3 to 5 = layer 0 to 2; bit 6 = wire 9 to the LEDs)
    PORTD |= (1 << 6) | ((1 << level) << 3); // set the current level and pin 6 to high (9th LEDs off)

    uint8_t tmp = level * 9; // calculate the position in the frame

    // PORTB = 1..8
    // 0 = led is on, 1 = led is off
    PORTB = ~((frame >> tmp) & 0xff);

    if ( (((frame >> tmp) >> 8) & 0x01) )
        PORTD &= ~(1 << 6); // turn the 9th LED on if required

    // rotate through the 3 level
    level++;
    if (level > 2) level = 0;

}