45 lines
1.9 KiB
C
45 lines
1.9 KiB
C
|
|
||
|
|
#define FIRMWARE_VERSION "v0.3.0"
|
||
|
|
|
||
|
|
//#define DEBUG_NO_I2C
|
||
|
|
#define DEBUG_NO_SERIAL_MSG
|
||
|
|
|
||
|
|
#define WATCHDOG_TIMEOUT_S 5
|
||
|
|
|
||
|
|
#define INA226_I2C_ADDRESS 0x41
|
||
|
|
#define BME280_I2C_ADDRESS 0x76 // oder 0x77, je nach Verbindung des ADDR-Pins
|
||
|
|
#define OLED_I2C_ADDRESS 0x3C // -> the addresses like 0x78 which is selected on the chip is not correct
|
||
|
|
|
||
|
|
#define LOOP_INA226READ_DEMO_DELAY_MS 1000
|
||
|
|
#define LOOP_DISPLAY_DELAY_MS 5000 // 5 Sekunden
|
||
|
|
#define LOOP_DISPLAY_DEMO_DELAY_MS 1000
|
||
|
|
#define LOOP_HANDLE_CLIENT_DELAY_MS 250
|
||
|
|
#define LOOP_INA226CHECK_DELAY_MS 600000
|
||
|
|
#define LOOP_WLAN_CHECK_DELAY_MS 60000
|
||
|
|
|
||
|
|
#define OLED_SCREEN_WIDTH 128 // OLED display width, in pixels
|
||
|
|
#define OLED_SCREEN_HEIGHT 64 // OLED display height, in pixels
|
||
|
|
#define OLED_RESET_PIN -1 // Reset pin # (or -1 if sharing Arduino reset pin)
|
||
|
|
#define OLED_TEST_SIZE 2
|
||
|
|
|
||
|
|
#define DISPLAY_SWITCH_SHOWN_VALUE_COUNT 2
|
||
|
|
|
||
|
|
// default config values
|
||
|
|
#define DEFAULT_SHUNT_VOLTAGE_DROP 85.0 // mV
|
||
|
|
#define DEFAULT_SHUNT_CURRENT_MAX 100.0 // A
|
||
|
|
#define DEFAULT_TEMP_MIN 20.0 // °C environment
|
||
|
|
#define DEFAULT_TEMP_MAX 30.0 // °C environment
|
||
|
|
#define DEFAULT_HUMI_MIN 30.0 // % humidity
|
||
|
|
#define DEFAULT_HUMI_MAX 70.0 // % humidity
|
||
|
|
#define DEFAULT_CURRENT_MIN -100.0 // maximum continuous discharge current
|
||
|
|
#define DEFAULT_CURRENT_MAX 100.0 // maximum continuous discharge current
|
||
|
|
#define DEFAULT_MAX_CAPACITY 2500.0f
|
||
|
|
#define DEFAULT_INA226READ_DELAY_S 30 // 30 Sekunden default, overwritten by eeprom config
|
||
|
|
|
||
|
|
#define EEPROM_SIZE 100 // in byte
|
||
|
|
// EEPROM-Adresse, an der die globale Energiemenge gespeichert wird
|
||
|
|
#define EEPROM_ADDR_ENERGY 0
|
||
|
|
#define EEPROM_ADDR_CFG_START 8 // sizeof(struct EnergyData { float energy; uint16_t checksum; };
|
||
|
|
|
||
|
|
#define FIRMWARE_UPDATE_URL "http://192.168.0.142:8082/firmware.ino.bin"
|